Shopping Cart
Your Cart is Empty
Quantity:
Subtotal
Taxes
Shipping
Total
There was an error with PayPalClick here to try again
CelebrateThank you for your business!You should be receiving an order confirmation from Paypal shortly.Exit Shopping Cart

Float Power Systems & Controls

TOMORROW'S TECHNOLOGY TODAY

 FREQUENTLY ASKED QUESTIONS

Is Float Power Systems & Controls a registered firm and qualified Importers and

Exporters ?

Yes

Where is your registered place of operation ?

Bangalore City –Karnataka –India

Is Grouser as a product successful and well received and accepted by the customers ?

Yes, Grouser is in operation all over the world since the 1980’s , used extensively in

the Power Sector

Have you successfully field tested Grouser and received customer acceptance ?

Yes – Field Tested – and received testimonials – send in your request to view

customers testimonials using the contact form.

Can the Grouser be used On Line without seeking shut down ?

Yes Works on live systems up to 300 volt DC

Can it be used to test dead motors/ rotors/ thermocouples etc ?

Yes – by using TX MK II along with T 273 Transmitter and Receiver Locates faults in

machine windings/ Traces earth faults on thermocouples/Traces and locates multiple

faults on systems/Locates Earth faults on live DC circuits/ Does not effect system

integrity/ Unaffected by load current or ripple/ Can be tuned to the fault current only

For more technical details send in request using contact form.

Who are the manufacturers of Grouser ?

GFAL Limited

Time schedule for supply of equipment ?

Minimum of 180 days from the date of placing written confirmed order (Check for

actual delivery schedules

What is the warranty offered ?

Manufacturers product guarantee for workmanship and performance 12 months from

the date of manufacture and supply – Float Power Systems & Controls offer additional

180 days extended warranty and other benefits (Sure buy customers can seek details

using contact form)

What is the maximum fault which the instrument can detect ?

Sensitive to faults as high as 68k ohm

How is the fault traced ?

By using the sensing probe attached to the receiver in synchronization with the

Transmitter ( Seek for live on-line demonstration)

What are the problems which has been over come during the course of the

development of the product ?

Grouser will not interfere with sensitive equipment connected to the DC system and is

unaffected by ripple, or switching transients/ Grouser has overcome problems such as

spillover, inductive coupling, interference, capacitive coupling, spurious noise, etc.

What is the Principle of the Grouser ?

The principle of operation is straight forward inject small current at a specific

frequency, trace only the current flow at that specific frequency, where the current

flows to earth is where the fault or faults are.

Are the sensing heads available in one size or in different sizes ?

Four different sizes are available from 6mm, 30mm and 45mm, these are supplied as standard. A 55mm and 95mmhead are available as an optional extra.

What are the Frequencies at which the Grouser operates?

Transmitter

Battery powered transmitter outputs 9 volt RMS open circuit, 50mA short circuit. The

output frequency is pre-set at between 11.0 Hz and 12.0 Hz and factory matched to

the receiver frequency.

The unit can operate on live circuits up to 300 volt DC, it is fuse protected and has

semi rotary controls to prevent accidental operation.

Receiver

The frequency range is factory set between 11.2 and 11.8 Hz, this low, very precise

frequency enables the Grouser to operate with a clean signal even in “noisy”

conditions. There is also a 10 turn capacitive balance control that enables the

operator to cancel out capacitive signals and view the fault signal independent of

other factors.

What is Grumbler Instrument used for ?

Grumbler for LIVE LV/MV Cable Identifier The instrument is designed to assist users

in the identification of cables

Will Float Power Systems & Controls be able to import any equipment ?

Yes,any equipment , testing and measuring instruments as applicable to the Power

Sector and Telecommunication sector, and such equipments where the customer

places a specific request while providing the technical specification of the required

product

What are the other products that Float Power Systems & Controls would be able to

supply ?

Refer Product Line .

Some details with reference to Analyzer Unit / Tracking Unit?

Ground faults on battery operate DC Multi feeder Distribution System are very difficult

to find without proper instrumentation and training.

Analyzer Unit - Tracking Unit

Has been designed with a new microprocessor control instrument with a single

purpose “to analyze and locate even the most difficult faults on battery operate DC

Multi feeder Distribution System”, for the safeguard of the DC system integrity.

The Ground Fault Analyzer and Tracking instrument make use of a very small

interrupted and synchronize DC signal to analyze and locate DC ground faults on

multi feeder distribution system .

Note : All technical specification , and other conditions of sale subject to change

without notice .All products per manufacturers specification and supply schedule

only.

 FLOAT POWER SYSTEMS & CONTROLS © 2010

Recent Photographs

Recent Blogs

0